Search This Blog

Wednesday, 14 February 2018

Guide to Flash Bricked Redmi 5/Plus by TestPoint Method

Hei Redmi 5/Plus fans,

What's cooking with your Android One device? This the another volume for my "ifelixit" series. Xiaomi's Redmi device lineup has been refreshed with two new models: The Redmi 5 Plus and its smaller, cheaper sidekick, the Redmi 5. We’re fans of the Redmi range, which provides a strong design and specification, along with excellent value for money. This winning formula continues with the Redmi 5 Plus and Redmi 5. 

Given a Bricked Redmi 5/Plus or failing to boot after a disastrous flashing leaving the user with non-functional phone, that is, fastboot or recovery cannot be attain at all or failing to unlock but wishing to flash to enter EDL mode. Lets get a solution quick to get it, PC detected to flash the Official designated ROM back on your partially dead Redmi 5/Plus. Hence, what is the last resort before going to the service center. The ultimate solution is Test Point Method, which is to short-circuit the resistor to ground and get the PC to recognize the phone in Emergency Download (EDL) mode. I would not be recommending any Deep Flasher Cable (DFC), even though I was the first to use it effectively, even before there is a tutorial made on the MIUI Forum since the circuitry of the DFC is different for different Mi devices. Let's kick in the Test Point Method...


Tools:
  • Anti-static angle tweezer
  • Plastic Crowbar
  • Plastic Prying Tools
  • Plastic Antistatic Crowbar
  • 1.5 Philips screw driver

Firstly, we start off with swtiching off your phone, then remove the Hybrid SIM tray with the ejector pin.


Next use the plastic prying tool, kind of run it thru the slit around the phone, until it slowly giving more space to allow your fingernail to pry it open. Take extra care of the fingerprint mechanism ribbon cable which is on the back cover connected to the motherboard, dismantle it for easy access or to avoid mishap to the ribbon cable.


Then using a 1.5 Philips screw driver, remove the four (4) screws holding the tin plate, to access the the battery socket/terminal, as shown below:-


Followed by, unplugging the battery terminal connector.


Next, we deal with the Test Point for those having issue with their PC/Laptop not detecting Qualcomm HS-USB QDLoader 9008 under the Ports (COM & LPT) on their Device Manager.

Assuming, the phone has been pried opened. Here is the effective points.

Step One:
Make sure the Battery connector is dismantled.

Step Two:
Use a sharp pointed Angle Tweezer and short the Test points firmly, as shown below:-


Next, goto the Redmi 5/Plus Flashing Method section below, to revive your device.
Note: Advisable keep your PC sound level loud, which will help you to know of the activity of the connection.


Firstly, we start off with swtiching off your phone, then remove the Hybrid SIM tray with the ejector pin.


Next use the plastic prying tool, kind of run it thru the slit around the phone, until it slowly giving more space to allow your fingernail to pry it open. There not much to worry as the fingerprint mechanism, no longer built to the back cover connected by a ribbon cable which need extra care.


Followed by, unplugging the battery terminal connector, as shown below:-


Next, we deal with the Test Point for those having issue with their PC/Laptop not detecting Qualcomm HS-USB QDLoader 9008 under the Ports (COM & LPT) on their Device Manager.

Assuming, the phone has been pried opened. Here is the effective points.

Step One:
Make sure the Battery connector is dismantled.

Step Two:
Use a sharp pointed Angle Tweezer and short the Test points firmly, as shown below:-


Next, goto the Redmi 5/Plus Flashing Method section below, to revive your device.
Note: Advisable keep your PC sound level loud, which will help you to know of the activity of the connection.


Essentials:

Step One:
Immediately plug in your USD DATA Cable while keeping the Test Points short properly, and your PC/Laptop will notify you of a new device being connected and it will download the necessary driver for the Qualcomm HS-USB QDLoader 9008 under the Ports (COM & LPT) on the Device Manager as shown below:


Step Two:
Remove the Angle Tweezer. Thereafter, launch your Mi Flash Tool, as shown below:



That's it for this series of "ifelixit". Stay tuned for the Ported MIUI ROM for MI A1 for Mi A1 users. Coming soon for the MIUI-ers.



DISCLAIMER: DO ON YOUR OWN RISK. Flashing can potentially bricked or bootloop your device.
"Solving with simplicity"





at
Labels: , , , , , , , , , , ,

3 comments:

  1. Unknown12 May 2018 at 10:05

    I have followed the whole process and the flas also success still my phone reboots upto recovery screen. What to do?

    ReplyDelete
  2. roboto16 July 2018 at 10:21

    yongalah

    ReplyDelete
  3. Unknown9 October 2018 at 05:12

    hey there worked for me, redmi 5 plus was in a bootloop after wrong update by myself (haven't unlocked the bootloader). now i could flash the chin dev rom with miui 10. after that used the unlock tool from xiaomi and have to wait for 360 hours. after that i want to go back to global stable/dev. which methode can i use for that? recovery flash by the mi assistant or else?

    ReplyDelete

Subscribe to: Post Comments (Atom)

RedWolf TWRP, Root Support Incremental OTA - Redmi 3S/X

Hei Redmi 3S/Prime/3X fans, What have we here today? After fiddling around with your Redmi 3S and getting comfortable with it, you ...